Wagner Products a division of DiversiTech USA

Tattle-Tale Control Monitor

Identifies open controls in seconds. A single use monitoring device for determining which, safety control has opened in response to a malfunction.
Saves wasted hours tracing a safety control shutdown, even if intermittent. A quick, inexpensive way to visually spot where the problem is. Simply install in parallel with each safety control. When a control opens, the red indicator flag pops up. You will know immediately which area of the system is experiencing problems.

• Disposable, safe, simple to use, and pocket sized
• Monitors safety controls, fuses, overload relays, motor protectors, freeze controls, limit controls, safety switches, fusible links, or steam control

CAUTION: Not to be used with lockout relays, use TC-007. Available in 24,110 & 240 volts.

WS-1 Wet Switch Flood Detector

The Wet Switch is solid-state device to eliminate flooding and damage to ceilings etc by either cutting the power to the unit and/or sending an alert signal. They are placed in the Air Conditioner's secondary pan and are activated with the detection of water.

• Now has a built-in test and reset button for easier installation
• Turns system off when detecting moisture due to condensate or drain leaks
• One or two drops will cause Wet Switch to turn off a unit, alerting a serviceman to a moisture problem
• A lit LED indicates the Wet Switch is activated and has turned the unit off
• Re-set simply by drying the absorbent pad with a paper towel and pressing the reset switch
• Connects to 24 VAC
• More than one unit may be connected to a system
• 2 amp contact rating
• Simple 3 wire installation
• Sales displays available
• U.S. Patent No. 4,787,212

DSP-1

Digital Single-Phase Line Voltage Monitor and motor protector. This device works automatically by continuously monitoring the incoming voltage and will detect any deviations outside the user selectable range. If the voltage is outside the range a timer begins to count down to shut down the power.

Automatic voltage monitor and control system. Continuously measures incoming line voltage, allowing detection of any voltage outside the tolerances that you set. If these limits are exceeded, the response timer begins counting.You may also set response time � a short time for a quick response or a long time to avoid nuisance tripping. If the voltage remains outside the tolerance after the time has elapsed, the DSP-1 will turn off its output relay and protect your device. While output is off, an additional delay timer activates to avoid rapid restarts.

• Digital voltmeter displays instantaneous line voltage
• Automatic voltage tester adjusts from 90 to 300 volts
• Adjustable response timer (0.1 to 10 sec.) prevents nuisance tripping
• Adjustable delay timer (1 to 720 sec.) prevents rapid restarts
• Digital display makes for easy viewing and operation

• Voltmeter: 70 to 325 Volts
• Voltage Set Point: 90 to 300 Volts
• Tolerance Limits: 6 to 18%
• Response Timer: 0.1 to 10 seconds
• Delay Timer: 1 to 720 seconds
• Output Relay: 10 Amps, 250 VAC resistive, single-pole/double-throw
• Control Input: 18 to 250 VAC with anticipator load for 24 volt thermostats

DTP-3

Digital Three Phase Motor Protector & Line Voltage Monitor Similar to the DSP-1 for three phase operations with additional features and benefits.

• Digital voltmeter displays instantaneous line voltage for all 3 phase pairs
• Contactor load side monitor checks for contactor closure
• One button contactor load side voltage measurement
• Automatic voltage tester adjusts from 160 to 600 volts
• Adjustable response timer (0.1 to 20 sec.) prevents nuisance tripping
• Adjustable delay on break (DOB) timer (0 to 720 sec.) prevents rapid re-starts
• Adjustable timer (0 to 30 sec.) allows sequencing of multiple units
• Off, Auto, On settings for operation with or without control inputs
• Selectable contactor test. Opens contactor if any one of 3 circuits fail
• Digital display makes for easy viewing and operation
• Fault memory records up to 25 fault causes

ADM (Delay on Make)

Ideal for random starting of multiple units.

HOW IT WORKS: These timers delay circuit closure upon application of power. Only after the set time period elapses and power remains ON will the circuit close, allowing the protected motor or compressor to start. For typical HVAC installations, timers are adjusted to random times to prevent power circuit overloads. They are sometimes called random start timers.

• Adjusts from 6 seconds to 8 minutes
• Spin proof knob
• Works with 24, 120 or 240 VAC control circuits
• Supports up to 1.5 Amps
• Two wire hookup for easy installation
• Solid state with quick-disconnect terminals
• Mounts with one self-tapping screw
• Conformal coated circuitry protects against moisture and shock
• UR recognized for US and Canada
• Works with anticipator type thermostats

007 Control Checker

A lifetime tool for monitoring and checking safety controls and operating controls.
One unit for all voltages 24-460 VAC or DC without switching dials or meters. Compact, 4 oz, reliable. Saves troubleshooting.
For normally closed controls, 007 connects in parallel with safety control. When the safety control opens in response to a problem in the system, 007 red LED turns on and remains on until reset manually.With intermittent problem, the LED remains on indicating the control is open. For operating controls, 007 verifies the status of all types indicating if there is power to the holding coil, the NC contact is open or closed, the thermostat contacts are open or closed, there is power to the contactor or starting holding coil, the overloads are open or closed, or there is a bad connection either on control or power side.

• Features battery check and reset switch
• Includes 9-volt battery
• 007 may be used over and over
• U.S. Pat. No. 4,092,625

NOTE: May use with lockout relays.